100kg/h Disc Crusher Machine

100kg/h Disc Crusher, Malt Mill Malt Crusher Grain Crusher, For Beer Equipment made of Stainless Steel

Quantity:
kg/h:	Please select 100
Availability:





Inquire Add to Basket

Product Description

Overview

CARRY-Disc Crusher for Beer brewing

Malt is the most expensive raw material in your beer. So to keep your cost down, you need to utilize as much of the available extract in the malt as possible. The malt mill is absolutely critical in getting the most out of your malt. A poor choice of mill could easily see you waste 5% of your malt.

Malt crushing equipment used disc-type malt mill or roller mill, powder size can be adjusted, a daily output less than 300L beer production line used disc-type malt mill, 500L or more used roller mill type. Tell us about your brewery and we’ll advise you on the right malt milling and handling equipment for your needs.

Product Description

The malt mill is the carrier of the craft, A good malt mill is the prerequisite for the quality of the craft beer. The effect of malt crushing affects the quality of craft beer; Grinding process requirements: to maintain the integrity of malt coat, and the starch of malt as possible as to be crushed;fine particles to be controlled at 1: 2.5

Disc Crusher

The steel discs of the CARRY disc mill can be used for dry grinding, high hardness steel discs. Innovative steel milling technology for smoother and more durable grinding

The capacitor shell is made of high-quality aluminum alloy material, which will not be crushed during transportation and prevent rust;

Capacity	Type	Dimension(mm)	Power
100KG/H	Disc	550300700	1.5KW

Q&A

The method and effect of malt smashing

Malt smashing usually use dry crushing, wet crushing, moisture regain grinding and consecutive humidifying crushing four ways.

Dry crushing: is a traditional crushing way, requires moisture of malt is better between 6%~8%.
Wet crushing: The malt is soaked in warm water of 20 ° C ~ 50 ° C for 15-20 minutes, so that the water moisture of the malt reaches 25% - 30%, and then pulverized by a wet malt miller.
Moisture regain grinding: also called humidification crushing, it is to send steam or a certain temperature of hot water to the malt in a short time to humidify the wheat hull, so that the husk is elastic and not broken, and remains relatively intact during crushing, which is favorable for filtration.
Consecutive humidifying crushing：organic combines wet crushing and humidification crushing, make malt entre to the soaking chamber during the function of adding material stick, then soaking it 60 seconds in warm water, so the moisture of malt can up to 23%~25%.The malt husk is elastic and then enters the malt miller. It is crushed and sprayed water at same time. After crushed, it falls into the mixing tank. After adding water and becoming thick liquid, it is pumped into the mashing pot.

What are the effects of mashing way to grinding degree?

At present, the mashing method mainly divided into two types, one is leaching mashing and another is boiling mashing.

The leaching mashing way don't need to steam and boil mashing wort, the dissolution and decomposition of the malt contents are carried out which happened below the boiling temperature, which requires the endosperm to be finely pulverized, and the mechanical cell wall is destroyed by mechanical pulverization to increase the contact area between the enzyme and the substrate.
The boiling mashing way is the concentrated wort that contains more particles heated to boiling temperature, it can compensate for the lack of mechanical grinding, so the crushed material can be slightly thicker. The more times you boil, the effective is better.

What are effects of filternation equipment to grinding degree?

The most common filtration equipment is lauter tank now, also very few parts is plate and frame filter press.
These two types of filtration equipment have differences for the ratio of each apart that required malt crushing material. The lauter tank uses the wheat hull as a natural filter layer.
When crushed, the wheat hull was broken out, the contents are separated from the wheat hull, the wheat hull is kept as intact as possible, and the endosperm is crushed by secondary or tertiary. When filtering with a plate and frame filter press, the wort is filtered by external pressure, and the wheat hull does not look so important when it was as a filter layer, so it can be crushed thinly.

How many ways of feeding in crushing system？

After crushed by the malt miller, then feed material by manual.
After crushed by the malt miller, then feed material by machine
After the malt miller is finished, it is sent to the powder bin by the conveyor/machine (above the mashing pot), and then directly dropped into the feeding port by the powder hopper.
After the malt miller is finished, it is sent to the powder bin (on the ground) by the conveyor, and then transported to the feed port through a conveyor.

Certificates